when i run Ultimate Edition 2.6 gamers off the live cd i have eth0, loopback and wireless just fine.
but when i install it to my hard drive i only have loopback and wireless. it does not see my earther net card!
when i run ifconfig - a this is what i get
ifconfig -a
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:3104 errors:0 dropped:0 overruns:0 frame:0
TX packets:3104 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:698388 (698.3 KB) TX bytes:698388 (698.3 KB)
wlan0 Link encap:Ethernet HWaddr 00:18:de:83:bf:a3
inet addr:192.168.1.244 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::218:deff:fe83:bfa3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:880080 errors:0 dropped:0 overruns:0 frame:0
TX packets:223466 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:640236696 (640.2 MB) TX bytes:28949388 (28.9 MB)
Are you a spammer
Please note, that the first 3 posts you make, will need to be approved by a forum Administrator or Moderator before they are publicly viewable.
Each application to join this forum is checked at the Stop Forum Spam website. If the email or IP address appears there when checked, you will not be allowed to join this forum.
If you get past this check and post spam on this forum, your posts will be immediately deleted and your account inactivated.You will then be banned and your IP will be submitted to your ISP, notifying them of your spamming. So your spam links will only be seen for an hour or two at most. In other words, don't waste your time and ours.
This forum is for the use and enjoyment of the members and visitors looking to learn about and share information regarding the topics listed. It is not a free-for-all advertising venue. Your time would be better spent pursuing legitimate avenues of promoting your websites.
Please note, that the first 3 posts you make, will need to be approved by a forum Administrator or Moderator before they are publicly viewable.
Each application to join this forum is checked at the Stop Forum Spam website. If the email or IP address appears there when checked, you will not be allowed to join this forum.
If you get past this check and post spam on this forum, your posts will be immediately deleted and your account inactivated.You will then be banned and your IP will be submitted to your ISP, notifying them of your spamming. So your spam links will only be seen for an hour or two at most. In other words, don't waste your time and ours.
This forum is for the use and enjoyment of the members and visitors looking to learn about and share information regarding the topics listed. It is not a free-for-all advertising venue. Your time would be better spent pursuing legitimate avenues of promoting your websites.
no eth0 when i install ubuntu to hard drive
5 posts
• Page 1 of 1
no eth0 when i install ubuntu to hard drive
by arctic_drifter » Fri Jun 04, 2010 3:31 pm
- arctic_drifter
- U.E. Newbie
- Posts: 2
- Joined: Fri Jun 04, 2010 3:16 pm
- Operating System: Ultimate Edition 3.1 32 BIT
Re: no eth0 when i install ubuntu to hard drive
by 2hot6ft2 » Fri Jun 04, 2010 4:34 pm
Hi arctic_drifter and welcome to the forum,
First we need to know what ethernet adapter you have so if you'll open a terminal and run
and post the results for the ethernet adapter we will have a better idea of what's going on.
First we need to know what ethernet adapter you have so if you'll open a terminal and run
- Code: Select all
lspci -nn
and post the results for the ethernet adapter we will have a better idea of what's going on.
HP G60-125NR - AMD Turion X2 64 - nVidia GeForce 8200M G - 128 GB SSD Dual boot - Ultimate Edition, Win 10 Pro
HP G60-121WM - AMD Sempron SI-40 - nVidia GeForce 8200M G - 128 GB SSD - Dual boot - Ultimate Edition, Win 10 Pro
Custom build, Rosewill Challenger ATX Gaming Case, AMD Phenom II x4 955 C3 rev., MSI 870A-G54, 2x ATI HD4850 512MB /256bit GDDR3 & dual precision, GSkill 8GB 1600 RAM - Multi boot - Ultimate Edition, Win 10 Pro, Beta Testing
-
2hot6ft2 - Moderator
- Posts: 533
- Joined: Sun May 25, 2008 12:30 pm
- Location: Alabama, USA
- Operating System: Ultimate Edition 3.2 64 BIT
Re: no eth0 when i install ubuntu to hard drive
by arctic_drifter » Fri Jun 04, 2010 5:09 pm
it is Broadcom Corporation BCM4401 -B0 100base-tx
- arctic_drifter
- U.E. Newbie
- Posts: 2
- Joined: Fri Jun 04, 2010 3:16 pm
- Operating System: Ultimate Edition 3.1 32 BIT
Re: no eth0 when i install ubuntu to hard drive
by Atriya » Sat Jun 26, 2010 12:01 pm
I have exactly the same problem on Ultimate Edition 2.7. Has this issue been resolved yet? This problem is keeping me from using Ultimate Edition, which is otherwise awesome.
- Atriya
- U.E. Newbie
- Posts: 3
- Joined: Sat Jun 26, 2010 11:57 am
- Operating System: Ultimate Edition 3.1 64 BIT
Re: no eth0 when i install ubuntu to hard drive
by Admin-Amir » Sat Jun 26, 2010 12:14 pm
Hello PPL.
It is well known the issues with Broadcom.
But you can try to download the Driver from here:
http://www.broadcom.com/support/ethernet_nic/4401.php
Unzip the file and try to install the Driver.
It is well known the issues with Broadcom.
But you can try to download the Driver from here:
http://www.broadcom.com/support/ethernet_nic/4401.php
Unzip the file and try to install the Driver.
- Admin-Amir
5 posts
• Page 1 of 1
Return to Ultimate Edition 2.6 (Including 2.6.5)
Who is online
Users browsing this forum: No registered users and 1 guest